UUltraTechGermany

For your home · fibre in the house

Fibre in your house, from the entry point to the router

The provider usually builds fibre only to the entry point in the basement or a fibre socket by the door. We take it from there to where you need it: plan the route, lay fibre or network cable, splice, measure and set up Wi-Fi across the house.

The fibre connection is there, but in the wrong place: the fibre socket is in the utility room with the fibre modem beside it, and the study in the attic gets barely any Wi-Fi. Which part the provider builds and which part you as the owner may prepare differs by provider. We clarify that with you first, lay the rest cleanly – through existing conduit, trunking or a new route – and hand over a measured connection.

  • Reply the same working day
  • Written quote
  • Anywhere in Germany
  • Payment after handover
For
House, flat
From
Entry point or fibre socket
To
Router, network sockets, Wi-Fi
Tools
Own splicing machine, measurement
Service area
Anywhere in Germany
Reply
The same working day
Payment
After handover

In plain words

Socket, modem, extension: what do they mean?

You will meet these terms as soon as the question is how the fibre gets through the house:

  • Building entry point (HÜP)

    The place where the provider’s fibre enters the house, usually in the basement or on an outside wall. The provider builds up to here.

  • Fibre socket (Gf-TA)

    The wall socket in the house where the fibre ends. It usually belongs to the provider, who decides whether it may be moved.

  • Fibre modem (ONT)

    A device that turns the light signal into a network signal. Some routers have it built in; with other connections it is a separate box in between.

  • Patch cable and extension

    A patch cable is a short fibre cable with a connector at each end. Behind the socket, a longer cable can bridge the way to the router if the connectors fit.

  • Loss (attenuation)

    The share of light lost on the way. Every connector and every tight bend costs a little. If the total loss is too high, too little light arrives.

  • Conduit

    A plastic tube in a wall or floor through which cables can be pulled without opening the wall.

Use cases

Typical jobs

Almost always one of these:

Services

What we take on

  • Site visit: entry point, fibre socket, where the router should go, possible route
  • Clarifying which part your provider builds and which part we lay
  • Laying fibre or network cable, in conduit or trunking
  • Splicing with our own machine where a fibre has to be joined
  • Measuring the route we laid
  • Network sockets in the rooms that need a cable
  • Router and Wi-Fi set up across the house, if wanted

What you get at handover

  • Sketch of the cable route
  • Measurements of the route we laid
  • Login details and a short guide to the home network

Set-up

Who does what?

A fibre connection has several parts. Ours is marked.

  1. 1
    Provider

    Provider

    Building entry point on the outside wall or in the basement

  2. 2
    Provider

    Provider

    Fibre socket and fibre modem

  3. 3
    Our part

    Our part

    Route, fibre or network cable to the router

  4. 4
    Our part

    Our part

    Router, network sockets, Wi-Fi across the house

Which part between the entry point and the fibre socket the provider builds differs by provider. We clarify it before the quote.

Cost

What does it cost?

Working time is charged, plus material and travel – all in the quote first.

ItemHow it is charged
Laying, splicing, measuring, set-upTime and materials, time estimated in the quote
Cable, conduit, sockets, trunkingItemised in the quote
TravelStated in the quote first
Working timeTime and materials, amount stated in the quote
BillingAt least 1 hour, then in full hours
PaymentAfter the work and handover: SEPA bank transfer, invoice or PayPal

What drives the price

  • Length of the route
  • Existing conduit or new openings
  • Number of rooms with a network socket
  • Wi-Fi set-up or not

Extra work that only shows up on site is agreed with you first – nothing is charged without your consent.

  • SEPATransfer
  • Invoice
  • PayPal

For your purchasing department

  • Quote

    In writing, up front: labour, material and travel are stated before any work starts.

  • Payment

    After the work and handover: SEPA bank transfer, invoice or PayPal. No prepayment.

  • Contact

    We reply the same working day, in English or German.

  • Supplier details

    UltraTech Germany · Leipziger Straße 40, 10117 Berlin, Germany · VAT ID DE463530263 · Legal notice

Quote

For an accurate quote

Photos help most.

  • Photo of the entry point and fibre socket
  • Where should the router go?
  • Which rooms need a cable?
  • Your provider
  • Is there conduit?

Process

How a job runs

  1. 1

    Enquiry

    You send photos of the entry point and fibre socket and say where the router should go.

  2. 2

    Site visit

    We look at the route and clarify what the provider does and what we do.

  3. 3

    Quote

    Working time, material and travel are fixed in the quote first.

  4. 4

    Installation and handover

    Lay, measure, set up, explain.

FAQ

Frequently asked questions

Can I have the fibre socket moved?

The fibre socket and the fibre modem usually belong to the provider, and the provider decides whether they may be moved. It is often simpler to leave the socket and run a network cable from the modem to the router. We clarify first what your provider allows.

Fibre or network cable to the router?

Behind the fibre modem a network cable is enough; copper carries the full speed of a home connection up to 100 metres. A second fibre is worth it when the modem itself has to move and the provider allows that.

Do walls have to be opened?

Not necessarily. Existing conduit, old phone or aerial lines as a draw wire, trunking and openings beside existing lines are often enough. What is needed shows at the visit and goes into the quote.

How long does it take?

In a single-family house with a free route usually a working day or less. The exact time is in the quote once we have seen the route.

Do you also do blocks of flats?

Yes, owners, owners associations and property managers have their own page: in-building fibre for multi-dwelling buildings, with riser, fire protection and the owners resolution.

Can fibre be extended inside the house?

Yes, but only the part behind the fibre socket (the Gf-TA in German). The provider’s line up to the socket belongs to the provider, and we do not change it. Behind the socket you can use a suitable fibre patch cable of the length you need, or we lay a fixed route and splice it. Which is better depends on the route and the connector type. Send us a photo of the socket and the router and we will tell you what to do.

How do I extend the fibre to a FRITZ!Box?

If your router has its own fibre port, the fibre cable runs from the socket straight into the router. If it should stand further away, you need a longer fibre cable with the right connectors, or a fixed route with a splice. What matters is the connector type on the router and your provider’s rules. The other way round also works: put the router next to the socket and use a network cable or Wi-Fi from there. Photos of the socket and the router help us find the simplest way.

How long may a fibre cable be inside a house?

We do not give a fixed maximum, because there is no blanket figure. What matters is how much light is lost on the way. Every connector, every joint and every tight bend costs a little; on house routes that usually counts for more than the length itself. In the end enough light must arrive. Whether it does on your route, we measure after laying. Your provider will tell you what they require.

How do you lay fibre in a single-family house?

First the route is decided: existing conduit, trunking or an old line as a draw wire. Then the cable is pulled in. Fibre cannot take sharp kinks or strong pull, so we lay wide bends and pull gently. At the end the fibres are spliced or fitted with connectors and the route is measured. You do not have to do any of it yourself. Send us photos of the connection and tell us where the router should go, and we will plan the route.

Do I need a new router when I get fibre?

That depends on your provider and your router. Some connections need a fibre modem of their own (an ONT), and your current router keeps working behind it. Other routers have a fibre port themselves. A router without a fibre port needs a modem in front of it. Whether your device fits is in its data sheet and in your provider’s documents. We set up router and Wi-Fi if you want. Tell us your provider and your router.

Sources

Standards and sources

Where a standard or a law gives a number, this page states it with its source. Where sources disagree, we give no number – your specification decides.

Show sources
  1. [1]DIN EN 50173, class D (Cat 5e): 100 m channel, 90 m permanent link – per Beckhoff Infosys, "Gesamte Übertragungsstrecke" (in German)

Enquiry about In-house fibre for private customers

  • Free initial consultation
  • Reply the same working day
  • Work by appointment
  • across Germany
Request a quote+49 30 50930365

For an accurate quote

  • Photo of the entry point and fibre socket
  • Where should the router go?
  • Which rooms need a cable?
  • Your provider
  • Is there conduit?
  • SEPATransfer
  • Invoice
  • PayPal