# Fibre in your house, from the entry point to the router

> The provider usually builds fibre only to the entry point in the basement or a fibre socket by the door. We take it from there to where you need it: plan the route, lay fibre or network cable, splice, measure and set up Wi-Fi across the house.

URL: https://utechit.de/home/fibre-connection
Alternate language version: https://utechit.de/de/home/glasfaser-hausanschluss
Language: en
Provider: UltraTech Germany, Leipziger Straße 40, 10117 Berlin
Service area: Deutschland

The fibre connection is there, but in the wrong place: the fibre socket is in the utility room with the fibre modem beside it, and the study in the attic gets barely any Wi-Fi. Which part the provider builds and which part you as the owner may prepare differs by provider. We clarify that with you first, lay the rest cleanly – through existing conduit, trunking or a new route – and hand over a measured connection.

## Socket, modem, extension: what do they mean?

You will meet these terms as soon as the question is how the fibre gets through the house:

- **Building entry point (HÜP)** — The place where the provider’s fibre enters the house, usually in the basement or on an outside wall. The provider builds up to here.
- **Fibre socket (Gf-TA)** — The wall socket in the house where the fibre ends. It usually belongs to the provider, who decides whether it may be moved.
- **Fibre modem (ONT)** — A device that turns the light signal into a network signal. Some routers have it built in; with other connections it is a separate box in between.
- **Patch cable and extension** — A patch cable is a short fibre cable with a connector at each end. Behind the socket, a longer cable can bridge the way to the router if the connectors fit.
- **Loss (attenuation)** — The share of light lost on the way. Every connector and every tight bend costs a little. If the total loss is too high, too little light arrives.
- **Conduit** — A plastic tube in a wall or floor through which cables can be pulled without opening the wall.

## Typical jobs

- **Router into the living room** — Fibre socket in the basement; router and Wi-Fi belong in the middle of the house.
- **Study in the attic** — A network cable upstairs instead of weak Wi-Fi.
- **Gigabit does not arrive** — The connection is fast, the home network slows it down.
- **Preparing for the provider** — Conduit and route ready before the provider comes.

## What we deliver

- Site visit: entry point, fibre socket, where the router should go, possible route
- Clarifying which part your provider builds and which part we lay
- Laying fibre or network cable, in conduit or trunking
- Splicing with our own machine where a fibre has to be joined
- Measuring the route we laid
- Network sockets in the rooms that need a cable
- Router and Wi-Fi set up across the house, if wanted

## Who does what?

A fibre connection has several parts. Ours is marked.

1. **Provider** — Building entry point on the outside wall or in the basement
2. **Provider** — Fibre socket and fibre modem
3. **Our part** — Route, fibre or network cable to the router
4. **Our part** — Router, network sockets, Wi-Fi across the house

Which part between the entry point and the fibre socket the provider builds differs by provider. We clarify it before the quote.

## What you get at handover

- Sketch of the cable route
- Measurements of the route we laid
- Login details and a short guide to the home network

## What does it cost?

Working time is charged, plus material and travel – all in the quote first.

- **Laying, splicing, measuring, set-up:** Time and materials, time estimated in the quote
- **Cable, conduit, sockets, trunking:** Itemised in the quote
- **Travel:** Stated in the quote first

What drives the price:

- Length of the route
- Existing conduit or new openings
- Number of rooms with a network socket
- Wi-Fi set-up or not

 Payment after installation and handover: SEPA bank transfer, invoice or PayPal.

## For an accurate quote

Photos help most.

- Photo of the entry point and fibre socket
- Where should the router go?
- Which rooms need a cable?
- Your provider
- Is there conduit?

## How a job runs

1. **Enquiry** — You send photos of the entry point and fibre socket and say where the router should go.
2. **Site visit** — We look at the route and clarify what the provider does and what we do.
3. **Quote** — Working time, material and travel are fixed in the quote first.
4. **Installation and handover** — Lay, measure, set up, explain.

## Frequently asked questions

### Can I have the fibre socket moved?

The fibre socket and the fibre modem usually belong to the provider, and the provider decides whether they may be moved. It is often simpler to leave the socket and run a network cable from the modem to the router. We clarify first what your provider allows.

### Fibre or network cable to the router?

Behind the fibre modem a network cable is enough; copper carries the full speed of a home connection up to 100 metres. A second fibre is worth it when the modem itself has to move and the provider allows that.

### Do walls have to be opened?

Not necessarily. Existing conduit, old phone or aerial lines as a draw wire, trunking and openings beside existing lines are often enough. What is needed shows at the visit and goes into the quote.

### How long does it take?

In a single-family house with a free route usually a working day or less. The exact time is in the quote once we have seen the route.

### Do you also do blocks of flats?

Yes, owners, owners associations and property managers have their own page: in-building fibre for multi-dwelling buildings, with riser, fire protection and the owners resolution.

### Can fibre be extended inside the house?

Yes, but only the part behind the fibre socket (the Gf-TA in German). The provider’s line up to the socket belongs to the provider, and we do not change it. Behind the socket you can use a suitable fibre patch cable of the length you need, or we lay a fixed route and splice it. Which is better depends on the route and the connector type. Send us a photo of the socket and the router and we will tell you what to do.

### How do I extend the fibre to a FRITZ!Box?

If your router has its own fibre port, the fibre cable runs from the socket straight into the router. If it should stand further away, you need a longer fibre cable with the right connectors, or a fixed route with a splice. What matters is the connector type on the router and your provider’s rules. The other way round also works: put the router next to the socket and use a network cable or Wi-Fi from there. Photos of the socket and the router help us find the simplest way.

### How long may a fibre cable be inside a house?

We do not give a fixed maximum, because there is no blanket figure. What matters is how much light is lost on the way. Every connector, every joint and every tight bend costs a little; on house routes that usually counts for more than the length itself. In the end enough light must arrive. Whether it does on your route, we measure after laying. Your provider will tell you what they require.

### How do you lay fibre in a single-family house?

First the route is decided: existing conduit, trunking or an old line as a draw wire. Then the cable is pulled in. Fibre cannot take sharp kinks or strong pull, so we lay wide bends and pull gently. At the end the fibres are spliced or fitted with connectors and the route is measured. You do not have to do any of it yourself. Send us photos of the connection and tell us where the router should go, and we will plan the route.

### Do I need a new router when I get fibre?

That depends on your provider and your router. Some connections need a fibre modem of their own (an ONT), and your current router keeps working behind it. Other routers have a fibre port themselves. A router without a fibre port needs a modem in front of it. Whether your device fits is in its data sheet and in your provider’s documents. We set up router and Wi-Fi if you want. Tell us your provider and your router.

## Standards and sources

- [DIN EN 50173, class D (Cat 5e): 100 m channel, 90 m permanent link – per Beckhoff Infosys, "Gesamte Übertragungsstrecke" (in German)](https://infosys.beckhoff.com/content/1031/ethernetcabling/1952405899.html)

## Contact

Email: info@utechit.de
Phone: +49 30 50930365


---

## Provider

UltraTech Germany, Leipziger Straße 40, 10117 Berlin
Email: info@utechit.de · Phone: +49 30 50930365 (WhatsApp)
More: https://utechit.de/llms.txt · MCP: https://utechit.de/api/ucp/mcp
